ThyssenKrupp Steelcom NZ Limited - Products Sheet Pile Tie Bars Macalloy 17MHS

Sheet Pile

Sheet Pile & EMV Hire

Vibro Hammers

Impact Hammers

Piling Rigs

Concrete Pile Breakers

Driving the Future
Piling Symposium
Video Footage

Sheet Pile Tie Bars > 17MHS

Upgraded - 17MHS 460 to 17MHS 520
Recently updated marine tie-bar system from 17MHS 460 to 17MHS 520.

The M520 is approximately 14% stronger than the traditional Grade 460, and will in some cases allow a smaller diameter bar to be used, thus offering significant savings.

The 17MHS 460 is still available until further notice.

Below is the Tendon Capabilities showing the increased yield loads.

Tendon Capabilities for Carbon 520
Thread	Units	M10	M12	M16	M20	M24	M30	M36	M42	M48	M56	M64	M76	M85	M90	M100
Nominal Bar Dia.	mm	10	11	15	19	22	28	34	39	45	52	60	72	82	87	97
Min. Yield Load	kN	28	41	77	122	176	284	411	566	746	1030	1360	1985	2531	2862	3585
Min. Break Load	kN	35	52	98	155	223	360	522	719	946	1308	1727	2520	3212	3633	4551
NominalBarWeight	Kg/m	0.50	0.75	1.40	2.20	3.00	4.80	7.10	9.40	12.50	16.70	22.20	32.00	41.50	46.70	58.00

ThyssenKrupp Steelcom sells and distribute sheet pile tie bars in Australia and New Zealand.

For inquiries, contact our Sales at 02 9409 1777 or 02 4966 0688.

ThyssenKrupp Steelcom sell 17MHS sheet pile tie bars. The 17MHS tie bars have been used in some of the most prestigious steel sheet piling projects in the world for over 45 years.

17MHS is a high strength weldable steel used as the standard bar for tie bars.

A wide range of compatible end connections and fittings have been developed to complement the range of bar diameters from M42 to M100 (smaller diameters are available on request).

Building on the success of the now standard 460 yield of the 17MHS grade tie bar, M105 rolled threads are now available, combined with the special to order 17MHS 500 grade material we can now provide a tie bar with a massive 3825 kN. yield load.

17MHS Fittings
Sheet Pile Tie Bars Fittings for MacAlloy 17MHS

Typical Details
Sheet Pile Tie Bars Typical Details

17MHS Load Properties
Thread type	Bar dia (mm)	Bar area (mm2)	Weight per metre (kg/m)	Thread pitch (mm)	Ultimate tensile load (kN)	Yield load (kN)	Permanent working load 0.5 Py (kN)	Temporary working load 0.625 Py (kN)
M42	39	1170	9.18	4.5	665	502	251	313
M48	44	1541	12.09	5	876	660	330	413
M56	52	2115	16.6	5.5	1209	912	456	570
M64	59	2789	21.9	6	1597	1204	602	753
M76	71	4026	31.6	6	2330	1757	879	1098
M90	85	5754	45.2	6	3360	2534	1267	1584
M100	95	7178	56.3	6	4208	3173	1587	1983

17MHS Mechanical Properties
Bar type	Ultimate tensile stress (N/mm2)	Min. Yield stress (N/mm2)	Min. elongation (%)	Charpy value at -20oC (J)	Young's Modulus (kN/mm2)	Standard bar length
17 MHS	610	460	19	27	205	12

17MHS Washer Plates
Thread	Bar diameter	Ref.No.	Larssen	Ref.No.	Frodingham	Ref.No.	FZ Piles
M42	39	WPL42	180x180x30	WPF42	180x180x30	WPZ42	180x180x30
M48	44	WPL48	180x180x30	WPF48	180x180x30	WPZ48	180x180x30
M56	52	WPL56	180x180x30	WPF56	180x180x30	WPZ56	200x200x30
M64	59	WPL64	180x180x30	WPF76	180x180x30	WPZ76	200x200x30
M76	71	WPL76	200x200x30	WPF76	180x180x30	WPZ76	200x200x30
M90	85	WPL90	200x200x30	WPF90	Bridging Plates	WPZ90	200x200x30
M100	95	WPL100	200x200x30	WPF100	Bridging Plates	WPZ100	200x200x40

17MHS Bearing & Anchor Plates
Thread	Bar Diameter	Ref.No.	Bearing Plate	Ref.No.	Anchor Plate
M42	39	BP42	180x180x30	AP42	300x300x25
M48	44	BP48	180x180x30	AP48	300x300x25
M56	52	BP56	180x180x30	AP56	400x400x25
M64	59	BP64	180x180x30	AP64	400x400x25
M76	71	BP76	200x200x40	AP76	475x475x35
M90	85	BP90	200x200x40	AP90	500x500x40
M100	95	BP100	200x200x40	AP100	550x550x45

17MHS Fittings
Bar Diameter	Thread	Fork End			Spade End			Common Dimentions					Pin
		Ref.No.	A	G	Ref.No.	B	T	C.Dia	D.Dia	E	Y	H	Ref.No.	P.Dia	M
39	M42x4.5	FE42	232	39	SE42	284	35	60	43	69	77	107	PE42	42	78
44	M48x5	FE48	266	44	SE48	321	40	68	49	80	88	121	PE48	48	89
52	M56x5.5	FE56	314	49	SE56	364	45	80	57	96	99	145	PE56	56	100
59	M64x6	FE64	348	59	SE64	408	55	91	65	110	119	167	PE64	64	120
71	M76x6	FE76	410	76	SE76	471	70	108	78	131	148	199	PE76	76	149
85	M90x6	FE90	489	86	SE90	555	80	129	96	161	170	246	PE90	95	171
95	M100x6	FE100	555	91	SE100	625	85	143	111	188	181	287	PE100	110	182

Bar Diameter	Thread	Nuts			Washers			Couplers			Turnbuckles
		Ref.No.	A/F	L	Ref.No.	O/D	T	Ref.No.	O/D	L	Ref.No.	O/D	L	K
39	M42x4.5	NM42	65	34	WM42	78	7	CE/42	63	84	TE/42	63	184	100
44	M48x5	NM48	75	38	WM48	92	8	CE/48	71	96	TE/48	71	196	100
52	M56x5.5	NM56	85	45	WM56	105	9	CE/56	80	112	TE/56	80	208	100
59	M64x6	NM64	95	51	WM64	115	9	CE/64	95	133	TE/64	95	212	100
71	M76x6	NM76	110	61	WM76	135	10	CE/76	112	157	TE/76	112	252	100
85	M90x6	NM90	130	72	WM90	160	12	CE/90	132	185	TE/90	132	280	100
95	M100x6	NM100	145	80	WM100	175	14	CE/100	140	205	TE/100	140	300	100

Click here to view the 520 Brochure as a pdf.

top


Privacy Policy \| Sitemap				Copyright © by ThyssenKrupp Steelcom NZ Limited